Renesas M302N2T-PRB Manual de usuario

M302N2T-PRBPod Probe for M302N1 and M302N2 Group MCUsUser's ManualRev.1.00September 1, 2003REJ10J0282-0100Z

( 10 / 38 )IMPORTANTNote on Clock Supply to the MCU:• Clock can be supplied to the evaluation MCU in one of the following two ways. This is determined

( 11 / 38 )IMPORTANTNote on the Work Area:• When using this product, set to "2C00h" as a start address of the work area at the time of start

( 12 / 38 )MEMO

( 13 / 38 )Chapter 2. PreparationThis chapter describes the package components, the system configuration and the preparation for using this product fo

( 14 / 38 )Chapter 2. Preparation2.1 Package ComponentsThis product consists of the following items. When unpacking, check to see if your product pack

( 15 / 38 )2.3 System ConfigurationFigure 2.1 System configurationProducts (1) and (2) shown in Figure 2.1 are included with this product. Get (3) and

( 16 / 38 )MEMO

( 17 / 38 )Chapter 3. Setting UpThis chapter describes switch settings required for using this product and how to connect this product to the PC4701 a

( 18 / 38 )Figure 3.1 Positions of the switches and their factory-settingsTable 3.1 Switch settings of the FLX64-PRBSwitch No. Switch settingFunctionS

( 19 / 38 )3.2 A-D Conversion Bypass CapacitorThis product has foot patterns on the board for mounting a bypass capacitor for the A-D convertercircuit

( 2 / 38 )• TQPACK080SB, TQSOCKET080SBG, YQPACK056SB, NQPACK056SB and YQ-GUIDE are products of Tokyo Eletech Corporation.Keep safety first in your cir

( 20 / 38 )Figure 3.4 Removing pod probe M302N2T-PRB(1) Unscrew the two screws of the M302N2T-PRB.(2) Remove the M302N2T-PRB from the FLX64-PRB. Inthi

( 21 / 38 )3.4 Connecting the Target SystemThere are three ways available to connect this product to target systems as shown in Figure 3.5.Figure 3.5

( 22 / 38 )The emulation pod for M302N2 Group needs the pitch converter board FLX-80QSB or DIRECT80Sand the emulation pod for M302N1 Group needs the p

( 23 / 38 )Figure 3.7 shows how to connect the pitch converter board M302N1T-56FPB for 56-pin 0.65-mm-pitch QFP.Figure 3.7 Connecting the pitch conver

( 24 / 38 )3.5 Procedures for Making MCU File for M3T-PD30It is necessary to change the contents of the MCU file according to the MCU to be developed.

( 25 / 38 )Chapter 4. SpecificationsThis chapter describes specifications of this product.4.1 Specifications ...

( 26 / 38 )Chapter 4. Specifications4.1 SpecificationsTable 4.1 lists the specifications of the M302N2T-PRB.Table 4.1 Specifications of M302N2T-PRBPC4

( 27 / 38 )4.2 External Dimensions(1) External Dimensions of Pod ProbeFigure 4.1 shows the external dimensions of the pod probe M302N2T-PRB.Figure 4.1

( 28 / 38 )(3) External Dimensions of Converter Board (M302N1T-56FPB)Figure 4.3 shows the external dimensions and a sample foot pattern of the pitch c

( 29 / 38 )Chapter 5. TroubleshootingThis chapter describes how to troubleshoot when this product does not work properly.5.1 When the Emulator Debugge

( 3 / 38 )PrefaceThe M302N2T-PRB is a pod probe for the M302N1 and M302N2 Group of Renesas 16-bit MCUs.The M302N2T-PRB is used by connecting to the PC

( 30 / 38 )Chapter 5. TroubleshootingWhen this product does not work properly, check the following.5.1 When the Emulator Debugger Does Not Start Up Pr

( 31 / 38 )(2) Errors Occur When Starting Up the Emulator Debugger(When the target system is connected)Table 5.2 Checkpoints of errors when starting u

( 32 / 38 )(3) Errors Occur When Starting Up the Emulator Debugger(When the target system is not connected)Table 5.3 Checkpoints of errors when starti

( 33 / 38 )Chapter 6. Maintenance and WarrantyThis chapter describes how to maintenance, repair provisions and how to request for repair.6.1 Maintenan

( 34 / 38 )Chapter 6. Maintenance and Guarantee6.1 MaintenanceIf dust or dirt collects on any equipment of your emulation system, wipe it off with a d

( 35 / 38 )6.4 How to Request for RepairIf your product is found faulty, follow the procedure below to send your product for repair.Customer Fill in t

( 36 / 38 )MEMO

M302N2T-PRB User's ManualRev.1.00September 1, 2003REJ10J0282-0100ZCOPYRIGHT ©2003 RENESAS TECHNOLOGY CORPORATIONAND RENESAS SOLUTIONS CORPORATION

( 4 / 38 )ContentsTerminology ...

( 5 / 38 )TerminologySome specific words used in this user's manual are defined as follows:Emulation pod main unitThis means the emulation pod M3

( 6 / 38 )MEMO

( 7 / 38 )Chapter 1. Precautions for SafetyThis chapter describes precautions for using this product safely and properly. For precautions for the emul

( 8 / 38 )Chapter 1. Precautions for SafetyIn both the user's manual and on the product itself, several icons are used to insure proper handlingo

( 9 / 38 )IMPORTANTNote on Final Evaluation:• Be sure to evaluate your system and make final confirmation with an CS (Commercial Sample)version MCU.No