Renesas SH7050 Series Manual de usuario

To our customers, Old Company Name in Catalogs and Other Documents On April 1st, 2010, NEC Electronics Corporation merged with Renesas Technology C

i Preface The HS7058ECB61H is a user system interface board that connects a user system for the SH7058 BP-272 package to the SH7058 E6000H emulator (

ii Contents Section 1 Configuration...1 Section 2 Connection Pr

1 Section 1 Configuration Figure 1 and table 1 show the configuration and components of the user system interface board for the BP-272 package. Pl

2 CAUTION Use a TQPACK256RD socket and CSPACK256Z202H01 (manufactured by Tokyo Eletech Corporation) for the BP-272 package IC socket and IC

3 Section 2 Connection Procedures 2.1 Connecting User System Interface Board to User System WARNING Always switch OFF the user system and the

4 (4) Notes on soldering the IC socket a) The IC socket is larger than the actual IC package; therefore, refer to figure 4 for the installation of o

5 CAUTION 1. Never dip the IC socket in flux or use wash to clean the IC socket. This is because flux may remain inside the IC socket du

6 2.1.2 Fastening IC Socket Connector CAUTION 1. Check the location of pin 1 before inserting. 2. Use a provided screwdriver. 3. Stop tight

7 2.2 Exchanging the Spacer of the EV-Chip Board While the user system interface board is connected to the user system, force must not applied to th

8 2.3 Connecting User System Interface Board to EV-Chip Board WARNING Observe the precautions listed below. Failure to do so will result in

Notice 1. All information included in this document is current as of the date this document is issued. Such information, however, is subject to chang

9 Connector No.UCN1 UCN1UCN2 UCN2BoardEV-Chip Board Connector No.Board Connector No.EV-chip board Figure 4 Connecting User System Interface Board t

10 2.4 Recommended Dimensions for User System Mount Pad (Footprint) Figure 5 shows the recommended dimensions for the mount pad (footprint) for the

11 2.5 Dimensions for EV-Chip Board and User System Interface Board The dimensions for the EV-chip board and the user system interface board are sho

12 2.6 Resulting Dimensions after Connecting User System Interface Board The resulting dimensions, after connecting the user system interface board

13 Section 3 Verifying Operation 1. Turn on the emulator according to the procedures described in the SH7058 E6000H Emulator User's Manual (H

14  To use the crystal oscillator mounted on the EV-chip board Install a crystal oscillator into the crystal oscillator terminals on the EV-chip b

15 Section 4 Notice 1. The MCU cannot be installed directly into the IC socket provided for connecting this user system interface board. 2. Befor

SH7058 Group BP-272User System Interface board HS7058ECB61H User's ManualPublication Date: Rev.2.00, November

1753, Shimonumabe, Nakahara-ku, Kawasaki-shi, Kanagawa 211-8668 JapanSH7058 Group BP-272User System Interface BoardREJ10B0088-0300HHS7058ECB61H User’

SH7058 Group BP-272User System Interface BoardHS7058ECB61H User’s ManualUser’s Manual Rev.3.0 2004.03Renesas Microcomputer Development Environment S

Cautions Keep safety first in your circuit designs! 1. Renesas Technology Corp. puts the maximum effort into making semiconductor products better an

I IMPORTANT INFORMATION READ FIRST • READ this user's manual before using this user system interface board. • KEEP the user's manual handy

II LIMITED WARRANTY Renesas warrants its user system interface boards to be manufactured in accordance with published specifications and f

III State Law: Some states do not allow the exclusion or limitation of implied warranties or liability for incidental or consequential damages,

IV SAFETY PAGE READ FIRST • READ this user's manual before using this user system interface board. • KEEP the user's manual handy for futur

V WARNING Observe the precautions listed below. Failure to do so will result in a FIRE HAZARD and will damage the user system and the emul