Renesas Emulation Pod forM16C/20 Series M30200T-RPD-E Información técnica Pagina 1

To our customers, Old Company Name in Catalogs and Other Documents On April 1st, 2010, NEC Electronics Corporation merged with Renesas Technology C

( 8 / 32 )Things to Check When UnpackingThe M30200T-RPD-E consists of the following parts and manuals. When unpacking, check to seeif your M30200T-RPD

( 9 / 32 )Chapter 1. Precautions for SafetyIn both the user's manual and on the product itself, several icons are used to insure proper handlingo

( 10 / 32 )WARNINGWarning for Installation:• Do not set this product in water or areas of high humidity. Make sure that the emulation pod mainunit doe

( 11 / 32 )Notes on the Target System:•Because the emulation pod main unit does not have the capacity to supply power to other devices,design your sys

( 12 / 32 )IMPORTANTNotes on Connecting Pod Probe and Pitch Converter Board:• Prepare the right pod probe for your MCU. Without a pod probe this produ

( 13 / 32 )Notes on MAP References and Settings:• When starting up M30200T-RPD-E, initial MAP settings are as follows.0000016 to 003FF16: EXT0040016 t

( 14 / 32 )Note on BRK Instruction:• BRK instruction cannot be used.Note on Software Break and Hardware Break:•A software break and a hardware break c

( 15 / 32 )Chapter 2. IntroductionM30200T-RPD-E is used by connecting to the PC4701 emulator main unit. Figure 2.1 shows thesystem configuration.Figur

( 16 / 32 )Chapter 3. SpecificationsTable 3.1 lists the specifications of M30200T-RPD-E.Table 3.1 Specifications of M30200T-RPD-EUsable emulator main

( 17 / 32 )Chapter 4. Setting Up4.1 Removing the Upper CoverIf you need to change the input frequency, remove the upper cover of the product to change

Notice 1. All information included in this document is current as of the date this document is issued. Such information, however, is subject to chang

( 18 / 32 )4.2 Setting Oscillation FrequencyWhen you are using the emulation pod main unit's internal oscillator, see (1) below, and when youare

( 19 / 32 )Figure 4.3 Circuit of oscillator board OSC-2Figure 4.3 shows the OSC-2 circuit. Use the circuit constants recommended by themanufacturer of

( 20 / 32 )Figure 4.4 Replacing small oscillator circuit boardsHow to replace the oscillator circuit board is shown in Figure 4.4 below.(1) Unscrew th

( 21 / 32 )Figure 4.5 External oscillator circuitFigure 4.6 Circuit in which oscillation does not occur(2) Using target system's oscillatora. To

( 22 / 32 )Chapter 5. Connection5.1 Connection to the Emulator Main UnitUse the FLX120-RPD 120-pin flexible cable (included with the package) to conne

( 23 / 32 )5.2 Connection to the Emulation PodAttach the FLX120-RPD to M30200T-RPD-E, then secure them with the screws. Figure 5.2 showshow to connect

( 24 / 32 )5.3 Connection to the Pod ProbeThe emulation pod for M16C/20 Series consists of the M30200T-RPD-E emulation pod main unitand the M302xxT-PR

( 25 / 32 )Chapter 6. External DimensionsFigures 6.1 shows external dimensions of M30200T-RPD-E.Figure 6.1 External dimensions of M30200T-RPD-EUnit: m

( 26 / 32 )Figure 6.2 External dimensions of FLX64-PRBUnit: mmFigures 6.2 shows external dimensions of the FLX64-PRB pitch converter board for connect

( 27 / 32 )Chapter 7. Maintenance and Guarantee7.1 MaintenanceIf dust or dirt collects on any equipment of your emulation system, wipe it off with a d

M30200T-RPD-EUser’s ManualUser’s ManualRev.1.00 2003.09Emulation Pod forM16C/20 Series

( 28 / 32 )7.4 How to Request for RepairIf your product is found faulty, follow the procedure below to send your product for repair.Customer Fill in t

( 29 / 32 )Chapter 8. TroubleshootingWhen the M30200T-RPD-E does not work properly, check the items listed below.(1) The emulator main unit cannot be

( 30 / 32 )MEMO

M30200T-RPD-E User's ManualRev.1.00September 1, 2003REJ10J0264-0100ZCOPYRIGHT ©2003 RENESAS TECHNOLOGY CORPORATIONAND RENESAS SOLUTIONS CORPORATI

1753, Shimonumabe, Nakahara-ku, Kawasaki-shi, Kanagawa 211-8668 JapanM30200T-RPD-EREJ10J0264-0100ZUser’s Manual

( 2 / 32 )Keep safety first in your circuit designs!• Renesas Technology Corporation and Renesas Solutions Corporation put the maximum effort into mak

( 3 / 32 )PrefaceThe M30200T-RPD-E is an emulation pod main unit for M16C/20 Series of Renesas 16-bitmicrocomputers. The M30200T-RPD-E is used by conn

( 4 / 32 )ContentsSummary...

( 5 / 32 )Chapter 6. External Dimensions ...25Chapter 7. Maint

( 6 / 32 )SummaryChapter 1. Precautions for SafetyThis chapter describes the precautions which should be taken in order to use M30200T-RPD-E safelyand

( 7 / 32 )TerminologySome specific words used in this User's Manual are defined as follows:Emulator systemThis means an emulator system built aro