Renesas M16C/6NN Manual de usuario

REJ10J1253-0300 E8 EmulatorRev.3.00 November 01, 2006 Additional Document for User's ManualR0E000080KCE00EP4Renesas Microcomputer Development

6

Section 4 Example of E8 Connection The connecting examples are shown as follows. When using the emulator as a programmer, the specification of conne

(2) In single-power supply and memory expansion mode P65P66P67CNVssRESETVccVccVccVccUser logicVcc*User SystemPulled-up at 4.7Ω or morePulled-down

(3) In dual-power supply and single-chip mode ＊：Open-collector bufferP65P66P67CNVssRESETVcc1Vcc1Vcc1Vcc1User logicVcc1*User systemPulled-up at 4.7k

(4) In dual-power supply and memory expansion mode *: Open-collector bufferP65P66P67CNVssRESETVcc1 Vcc1 Vcc1 Vcc1User logicVcc1*User SystemPulled-

Notes: 1. P64, P65, P66 and P67 pins are used by the E8 emulator. Connect the E8 emulator to the MCU pins. Pull up MCU pins and connect the E8

(3) In dual-power supply and single-chip mode P50/CEEPMCEUser system connectorPulled-up at 4.7kΩ or moreVcc212 Figure 4.8 Connection of E8 Emu

4. The RESET pin is used by the E8 emulator. Therefore use an open-collector output buffer or a CR reset circuit as the reset circuit of the user sy

10. Figure 4.12 shows the interface circuit in the E8 emulator. Use this figure as a reference when determining the pull-up resistance value. RxDSC

Section 5 Notes on Using the E8 Emulator 1. Program area for the E8 emulator Table 5.1 lists the program area for the E8 emulator. Do not chang

1. Renesas Technology Corp. puts the maximum effort into making semiconductor products better and mor

Figure 5.1 [Firmware Location] Tab of the [Emulator Setting] Dialog Box 2. When the emulator system is initiated, it initializes the general reg

5. SFR used by the program for the E8 emulator As the SFR listed in Table 5.3 is used by the program for the E8 emulator, do not change a value. O

7. Debugging of the watchdog timer When debugging the user program using the watchdog timer, select the [Debugging of program that uses WDT.] chec

Figure 5.3 [ID Code verification] Dialog Box [Note on Program Flash mode] When the ID code is specified by the -ID option of the lmc30, download th

15. Reserved area The addresses not specified in the Hardware Manual for the M16C/62P and M16C/6N Groups are reserved area. Do not change the conte

19. “Go to cursor” function The "Go to cursor" function is realized by using an address match break. Therefore, when you execute the Go

24. Notes on the E8 emulator power supply When writing reliability required program with the E8 emulator under the mass production, do not use th

Section 6 Setup the Debugger 1. Emulator Setting dialog box [Emulator Setting] dialog box is provided for setting the items that need to be set w

2. Emulator mode Tab The selection of the device, the specification of the mode, and the setting of the power supply are done in the [Emulator mode]

4 MCU Setting Tab In the [MCU Setting] tab, set the operating condition of MCU used in the user system. Figure 6.3 [MCU Setting] Dialog Box Spe

Contents Section 1 Specifications of the E8 Emulator...

Section 7 Command for Memory Space Expansion Function 4MB Mode 1. Command for Memory Space Expansion Function 4MB Mode The followings show the comm

Memory_Display_Ext Abbreviation: MDE Description: Displays memory contents. This cannot be used during the program execution. Syntax: MDE MDE <ban

28 Memory_Find_Ext Abbreviation: MIE Description: Finds a string in a memory range. This cannot be used during the program execution. Syntax: MIE &l

Section 8 Applicable Tool Chain and Partner Tools With the M16C/62P and M16C/6N Groups E8 emulator, you can debug a module created by the inhouse to

*.cpp main() { class DerivedClass ClassObj; ClassObj.DerivedFunc(); return; } void BaseClass::BaseFunc(void) { m_iBase = 0x1234; } void DerivedC

E8 Emulator Additional Document for User's Manual Notes on Connecting the M16C/62P, M16C/6N4, M16C/6N5, M16

E8 EmulatorAdditional Document for User's Manual

Section 1 Specifications of the E8 Emulator Table 1.1 shows the specifications of the M16C/62P and M16C/6N Groups E8 Emulator. This manual describes

2

Section 2 Connecting the Emulator with the User System Before connecting an E8 emulator with the user system, a connector must be installed in the u

4

Section 3 Pin Assignments of the E8 Connector Figure 3.1 shows the pin assignments of the connector. 5 P50(CE)VssPin 1 mark Pin 2 Pin 1 mark Conn