Renesas H8S/2214 Series Manual de usuario

I IMPORTANT INFORMATION READ FIRST • READ this user's manual before using this user system interface cable. • KEEP the user's manual handy

Section 1 Configuration CAUTION Use an NQPACK100SE socket (manufactured by Tokyo Eletech Corporation) for the TFP-100G package IC socket on

2 Table 1 lists the HS2218ECN61H components. Please make sure you have all of these components when unpacking. Table 1 HS2218ECN61H Components No.

Section 2 Connection Procedures 2.1 Connecting User System Interface Cable to Emulator Station WARNING Observe the precautions listed below. F

Emulator stationCable body connectorScrews for fixingthe cable bodyUser system interface cableE6000 Figure 2 Connecting User System Interface Cable

2.2 Connecting User System Interface Cable to User System WARNING Always switch OFF the user system and the emulator product before the USER S

User systemIC socket(NQPACK100SE manufactured by Tokyo Eletech Corporation)Guide pins4 projections to applyepoxy resin adhesive toBottom view of IC s

7 2.2.4 Fastening Cable Head CAUTION 1. Use a screwdriver whose head matches the screw head. 2. The tightening torque must be 0.054 N•m or les

Pin 1Cable headIC socket (NQPACK100SEmanufactured by Tokyo Eletech Corporation)Screws (M2 x 10 mm)User system Figure 4 Connecting User System Interf

2.2.5 Fastening Cable Body Connect the cable body to the cable head. 9 Cable bodyCable headRemove jigPush the remove jigUser systemRemoving Figure 5

2.3 Recommended Dimensions for User System Mount Pad Figure 6 shows the recommended dimensions for the mount pad (footprint) for the user system with

II LIMITED WARRANTY Renesas warrants its user system interface cables to be manufactured in accordance with published specifications and f

2.4 Dimensions for User System Interface Cable Head The dimensions for the user system interface cable head are shown in figure 7. Unit: m

2.5 Resulting Dimensions after Connecting User System Interface Cable The resulting dimensions, after connecting the user system interface cable head

13 Section 3 Installing the MCU to the User System CAUTION 1. Check the location of pin 1 before inserting. 2. Use a screwdriver whose head m

14 Socket coverMCUPin 1IC socket (NQPACK100SEmanufactured by Tokyo Eletech Corporation)User systemScrews (M2 x 6 mm) Figure 9 Installing MCU to Use

Section 4 User Interface Circuit The user system interface cable includes the H8S/2218 microcomputer to emulate the USB function. The H8S/2218 user

Section 5 Verifying Operation 1. When using the H8S/2214 E6000 emulator for the H8S/2218 series, turn on the emulator according to the procedures d

Section 6 Notice 1. Make sure that pin 1 on the user system IC socket is correctly aligned with pin 1 on the cable head before inserting the cable

18 7. This emulator does not support mode 7 (single-chip mode). 8. In the H8S/2218 series, the USB control register and the RTC control register ar

III State Law: Some states do not allow the exclusion or limitation of implied warranties or liability for incidental or consequential damages,

SAFETY PAGE READ FIRST • READ this user's manual before using this user system interface cable. • KEEP the user's manual handy for future re

WARNING Observe the precautions listed below. Failure to do so will result in a FIRE HAZARD and will damage the user system and the emulato

H8S/2218 Series TFP-100G User System Interface Cable (HS2218ECN61H) for E6000 Emulator User’s Manual ADE-xxx-xxx Rev. 2.0 7/22/03 Renesas Technology

Cautions 1. Renesas neither warrants nor grants licenses of any rights of Renesas’s or any third party’s patent, copyright, trademark, or other intel

i Preface Thank you for purchasing this user system interface cable (HS2218ECN61H) for the Renesas’s original microcomputer H8S/2218 series. The HS22

ii Contents Section 1 Configuration.....................1 Section 2 Connection P