Renesas H8S/2276 Información técnica

To our customers, Old Company Name in Catalogs and Other Documents On April 1st, 2010, NEC Electronics Corporation merged with Renesas Technology C

IIIState Law: Some states do not allow the exclusion or limitation of implied warranties or liability forincidental or consequential damages, so t

IVSAFETY PAGEREAD FIRST• READ this user's manual before using this user system interface cable.• KEEP the user's manual handy for future ref

VWARNINGObserve the precautions listed below. Failure to do sowill result in a FIRE HAZARD and will damage the usersystem and the emulator product or

iPrefaceThank you for purchasing this user system interface cable (HS2276ECH61H) for the Hitachi’soriginal microcomputer H8S/2276R, H8S/2276 series.Th

iiContentsSection 1 Configuration...1Section 2 Connection Proced

1Section 1 ConfigurationCAUTIONUse an IC149-100-054-B51 socket (manufactured byYAMAICHI ELECTRONICS Co., Ltd.) for the TFP-100Bpackage IC socket on

2Table 1 lists the HS2276ECH61H components. Please make sure you have all of thesecomponents when unpacking.Table 1 HS2276ECH61H ComponentsNo. Compon

3Section 2 Connection Procedures2.1 Connecting User System Interface Cable to Emulator StationWARNINGObserve the precautions listed below. Failure

42. [1] After making sure the direction of the expansion board connector labeled E6000 EMULATOR is correct, firmly insert the expansion board connecto

Notice 1. All information included in this document is current as of the date this document is issued. Such information, however, is subject to chang

52.2 Connecting User System Interface Cable to User SystemWARNINGAlways switch OFF the user system and the emulatorproduct before the USER SYSTEM INTE

62.2.3 Inserting Cable HeadCAUTIONCheck the location of pin 1 before inserting.Align pin 1 on the IC socket for a TFP-100B package on the user system

7Fasten the user system interface cable head to the IC socket for a TFP-100B package on the usersystem with the four screws (M2.6 x 12 mm; with flat w

82.2.5 Fastening Cable BodyConnect the cable body to the cable head.Cable bodyCable headRemove jigPush the remove jigRemovingUser systemFigure 4 Fas

92.3 Recommended Dimensions for User System Mount PadFigure 5 shows the recommended dimensions for the mount pad (footprint) for the user systemwith a

102.4 Dimensions for User System Interface Cable HeadThe dimensions for the user system interface cable head are shown in figure 6.Figure 6 Dimensio

112.5 Resulting Dimensions after Connecting User System Interface CableThe resulting dimensions, after connecting the user system interface cable head

12Section 3 Installing the MCU to the User SystemCAUTION1. Check the location of pin 1 before inserting.2. Use a Philips-type screwdriver whose head

13Figure 8 Installing MCU to User System

14Section 4 Verifying Operation1. When using the H8S series E6000 emulator (HS2000EPI61H), turn on the emulator accordingto the procedures described

Regarding the change of names mentioned in the document, such as Hitachi Electric and Hitachi XX, to Renesas Technology Corp.The semiconductor operati

154. Subclock (OSC2, 1)When the switch is set on the expansion I/O board (Subclock selection) and jumper P4 is seton the user system interface cable,

16Figure 10 shows the Expansion I/O board Subclock Selection, and figure 11 shows the location ofjumper P4.Figure 12 shows the system clock oscillator

17Section 5 Notice1. Make sure that pin 1 on the user system IC socket is correctly aligned with pin 1 on the cablehead before inserting the cable h

Cautions Keep safety first in your circuit designs! 1. Renesas Technology Corporation puts the maximum effort into making semiconductor products bett

H8S/2276R, H8S/2276 Series TFP-100BUser System Interface Cable (HS2276ECH61H) for E6000 EmulatorUser’s ManualUser’s Manual Rev.1.0 2002.02

Cautions1. Hitachi neither warrants nor grants licenses of any rights of Hitachi’s or any third party’spatent, copyright, trademark, or other intellec

IIMPORTANT INFORMATIONREAD FIRST• READ this user's manual before using this user system interface cable.• KEEP the user's manual handy for f

IILIMITED WARRANTY Hitachi warrants its user system interface cables to be manufacturedin accordance with published specifications and free from d