Renesas R8C/Tiny Series Manual de usuario

REG10J0049-0200 Renesas Starter Kit for R8C/2D User’s Manual RENESAS SINGLE-CHIP MICROCOMPUTER M16C FAMILY / R8C/Tiny SERIES

6.4. Serial port This RSK provides two serial ports to the user. The serial port 1 has already been configured for use. To use serial port 2 the user

6.6. Option Links Table 6-5 below describes the function of the option links associated with Power configuration. The default configuration is indica

Table 6-7 below describes the function of the option links associated with serial configuration. The default configuration is indicated by BOLD text.

Table 6-9 below describes the function of the option links associated with serial configuration. The default configuration is indicated by BOLD text.

The Reset circuit operates by latching the state of the boot switch on pressing the reset button. This control is subsequently used to modify the mod

Chapter 7. Modes This Renesas Starter Kit supports Boot mode and Single chip mode. Details of programming the FLASH memory is described in the R8C/2

Chapter 8. Programming Methods The board is intended for use with High-performance Embedded Workshop and the supplied E8a debugger. Refer to R8C/2C

Chapter 9. Headers 9.1. Microcontroller Headers Table 9-1 to Table 9-4 show the microcontroller pin headers and their corresponding microcontroller

J3 Pin Circuit Net Name Device Pin Pin Circuit Net Name Device Pin 1 DLCD5 41 2 DLCD4 42 3 LED0 43 4 INT0n 44 5 TXD1 45 6 RXD1_INT3n* 4

9.2. Application Headers Table 9-5 to Table 9-8 below show the standard application header connections. * Marked pins are subject to option links.JA1

Table of Contents Chapter 1. Preface...

JA5 Pin Generic Header Name CPU board Signal Name Device Pin Pin Generic Header Name CPU board Signal Name Device Pin 1 AD4 AN4 69 2 AD5 AN5

Table 9-9 below shows the LIN header connections.J5 Pin Function Signal Name 1 Power Supply (for LIN module) VBAT 2 GROUND GND LIN Pin Function

Chapter 10. Code Development 10.1. Overview Note: For all code debugging using Renesas software tools, the Renesas Starter Kit board must be connect

10.4. Memory Map SFRInternalRAMInternalROM(Data Area)InternalROM(ProgramArea)00000h002FFh00400 h00FFFh02400 h02BFFh04000hFixed Vector Tables0FFFFh0FF

Chapter 11. Component Placement Figure 11-1 : Component Placement 22

Chapter 12. Additional Information For details on how to use High-performance Embedded Workshop, refer to the High-performance Embedded Workshop man

Renesas Starter Kit for R8C/2D User's Manual Publication Date Rev.2.00 12.OCT.2007 Published by: Renesas Solutions

Renesas Starter Kit for R8C/2D User's Manual Renesas Solutions Corp.Dukes Meadow, Millboard Road, Bourne

Chapter 1. Preface Cautions This document may be, wholly or partially, subject to change without notice. All rights reserved. Duplication of this do

Chapter 2. Purpose This Renesas Starter Kit is an evaluation tool for Renesas microcontrollers. Features include: • Renesas Microcontroller Progra

Chapter 3. Power Supply 3.1. Requirements This Renesas Starter Kit operates from a 3V to 5V power supply. A diode provides reverse polarity protecti

Chapter 4. Board Layout 4.1. Component Layout The following diagram shows the top layer component layout of the board. JA6MCUReset SwitchE8 Header U

4.2. Board Dimensions The following diagram gives the board dimensions and connector positions. All through hole connectors are on a common 0.1” grid

Chapter 5. Block Diagram Figure 5-1 is representative of the CPU board components and their connectivity. Boot mode pinsBOOTCircuitryD-typeLatchRESE

Chapter 6. User Circuitry 6.1. Switches There are four switches located on the board. The function of each switch and its connection are shown in Ta