Renesas M16C/6NK Información técnica

To our customers, Old Company Name in Catalogs and Other Documents On April 1st, 2010, NEC Electronics Corporation merged with Renesas Technology C

Chapter 5. Block Diagram Figure 5-1 is representative of the CPU board components and their connectivity. MicrocontrollerUser: 4 LEDS1Green, 1Oran

Chapter 6. User Circuitry 6.1. Switches There are four switches located on the RSK. The function of each switch and its connection are shown in Tabl

6.4. Serial port The microcontroller programming serial port 1 is connected to the RS232 connector. A serial port can be used by moving option resist

J11 Pin Circuit Net Name Device Pin Pin Circuit Net Name Device Pin 1 Ground - 2 5V Only - 3 No Connection - 4 DLCDRS 70 5 R/W (Wired to W

Table 6-7 below describes the function of the option links associated with Clock configuration. The default configuration is indicated by BOLD text.

Table 6-8 below describes the function of the option links associated with Serial configuration. The default configuration is indicated by BOLD text.

Table 6-9 below describes the function of the option links associated with Analog configuration. The default configuration is indicated by BOLD text.

Option Link Settings Reference Function Fitted Alternative (Removed) Related To R82 Microcontroller pin function select Connects microcontroller

Option Link Settings Reference Function Fitted Alternative (Removed) Related To R128 Microcontroller pin function select Connects microcontroller

6.7.Oscillator Sources A crystal oscillator is fitted on the RSK and used to supply the main clock input to the Renesas microcontroller. details th

Notice 1. All information included in this document is current as of the date this document is issued. Such information, however, is subject to chang

Chapter 7. Modes The RSK supports Boot mode and Single chip mode. Details of programming the FLASH memory is described in the M16C/6NK Group Hardwa

Chapter 8. Programming Methods The board is intended for use with HEW and the supplied E8a module. Refer to the M16C/6NK Group Hardware Manual for d

Chapter 9. Headers 9.1. Microcontroller Headers Table 9-1 to Table 9-4 show the microcontroller pin headers and their corresponding microcontroller

J3 Pin Circuit Net Name Device Pin Pin Circuit Net Name Device Pin 1 A19_LED3 49 2 A18_LED2 50 3 A17_LED1 51 2 A16_LED0 52 5 A15_IO7 53

9.2. Application Headers Table 9-5 and Table 9-6 below show the standard application connections. * Marked pins are subject to option links.JA1 Pin

Table 9-7 to Table 9-9 below show the optional generic header connections. * Marked pins are subject to option links. JA3 Pin Header Name RSK Signa

JA5 Pin Header Name RSK Signal Name Device Pin Pin Header Name RSK Signal Name Device Pin 1 ADC4 I4 AN4* 90 2 ADC5 I5 AN5* 89 3 ADC6 I6

Table 9-10 below shows the CAN connections J14 Pin Function Signal Name Device Pin 1 CAN0 Positive CAN0H 21 2 GROUND 3 CAN0 Negative CAN0

Chapter 10. Code Development 10.1. Overview Note: For all code debugging using Renesas software tools, the RSK board must be connected to a PC USB p

10.4. Memory Map Figure 10-1: Memory Map 25

Renesas Starter KitRSKM16C6NK User’s ManualUser’s ManualRev.2.00 2007.10RENESAS SINGLE-CHIP MICROCOMPUTERM16C FAMILY

Chapter 11.Component Placement Figure 11-1: Component Placement 26

Chapter 12. Additional Information For details on how to use High-performance Embedded Workshop (HEW, refer to the HEW manual available on the CD or

Renesas Starter Kit for M16C/6NK User's Manual Publication Date Rev.02.00 30.OCT.2007 Published by: Renesas Technolog

1753, Shimonumabe, Nakahara-ku, Kawasaki-shi, Kanagawa 211-8668 JapanRenesas Starter Kit for M16C/6NKREG10J0017-0200User’s Manual

Table of Contents Chapter 1. Preface...

Chapter 1. Preface Cautions This document may be, wholly or partially, subject to change without notice. All rights reserved. Duplication of this d

Chapter 2. Purpose This RSK is an evaluation tool for Renesas microcontrollers. Features include: • Renesas Microcontroller Programming. • User C

Chapter 3. Power Supply 3.1. Requirements This RSK operates from a 5V power supply. A diode provides reverse polarity protection only if a current l

Chapter 4. Board Layout 4.1. Component Layout The following diagram shows the top layer component layout of the board. E8a Header Figure 4-1: Board

4.2. Board Dimensions The following diagram gives the board dimensions and connector positions. All through hole connectors are on a common 0.1” grid