Renesas M16C/6V Información técnica descargar pdf (Pagina 20)

M306V8T-EPB User’s Manual 1. Outline

REJ10J0777-0100 Rev.1.00 2005.08.01 Page 18 of 90

1.4 Specifications

Tables 1.5 lists the specifications of the M306V8T-EPB.

Table 1.5 Specifications of the M306V8T-EPB

Applicable MCU M16C/60 Series M16C/6V Group M306V8

Applicable MCU mode Single-chip mode

Memory expansion mode 16 bit bus width (Normal, Memory expansion mode 2)

Microprocessor mode 16 bit bus width (Normal, Memory expansion mode 2)

Maxi. ROM/RAM capacity 1. MCU internal flash ROM: 516KB (0F000h--0FFFFh, 80000h--FFFFFh)

2. MCU internal RAM: 16KB (00400h--043FFh)

3. MCU internal flash OSDRAM: 4KB (08000h--08FFFh)

4. MCU internal flash OSDROM: 128KB (30000h--4FFFFh)

Applicable power supply Vcc1 = Vcc2 = Vcc3: 3.15--3.45 V

Maximum operating frequency Power supply voltage 3.15 to 3.45 V: 16 MHz

Emulation memory 1. Access area: Flash ROM of MCU

Max. operating frequency: 10 MHz

2. External area (CS3*--CS0* area) Possible to allocate up to 4 areas by 4 KB

- Maximum operating frequency (at 3.3 V) 0 wait: 6 MHz

1--3 wait: 16 MHz

Basic debugging functions - Download

- Address match break (max. 8 points)

- Software break (max. 64 points)

- Program execution/stop (allows free-run execution supporting software breaks)

- Memory reference/setting (reference/setting C-variables, run-time execution)

- Register reference/setting

- Disassemble display

- C-level debugging, etc.

Real-time trace function - 256K-cycle bus information recordable

(Bus, external trigger, time stamp)

- 5 trace modes supported (Break/Before/About/After/Full)

- Can be recorded ON/OFF by events

Real-time RAM monitor function - 4,096 bytes (256 bytes x16)

- Data/last access result

Hardware break function 8 points (Execution address, bus detection, interrupt, external trigger signal)

Execution time measurement function Time between program start and stop

Maximum/minimum/average execution time and pass count of specified four zones.

Count clock: Equal to MCU Clock or 16 MHz

C0 coverage 8,192 KB (256 KB x 32 blocks)

External trigger input/event output External trigger input (MCU-dependent-voltage CMOS level x8) or event output

(break x1, event x7)

Host machine interface - LPT parallel (ECP, EEP, Byte/compatibility and Nibble/compatibility modes)

- USB (USB 1.1, full-speed)*

- LAN (10BASE-T)

Power supply to emulator Supplied from included AC adapter (power supply voltage: 100--240 V, 50/60 Hz)

Connecting the User System

(see 2.9 "Connecting the User

System" on page 30)

M306V8T-PTC (pre-mounted) converter board for 116-pin 0.65-mm-pitch LQFP

(116P6A-A)

* Available to connect the host machine that supports USB 2.0.

With the USB interface, not all hardware (such as host machine, USB devices, USB hub) combination will work and

guaranteed.

1 2 ... 15 16 17 18 19 20 21 22 23 24 25 ... 91 92

Comentarios a estos manuales

Sin comentarios

Renesas M16C/6V Información técnica Pagina 20

Comentarios a estos manuales

Relacionado con productos y manuales para Redes Renesas M16C/6V