Renesas SDI Emulator System M32100T-EZ-E Información técnica Pagina 1

To our customers, Old Company Name in Catalogs and Other Documents On April 1st, 2010, NEC Electronics Corporation merged with Renesas Technology C

( 8 / 42 )Caution for Abnormal Operation:• If the emulator malfunctions because of interference like external noise, shut down the emulatoronce and th

( 9 / 42 )IMPORTANTNotes on Product Information:• For the information about this product, visit the Renesas Tool Homepage.http://www.renesas.com/eng/p

( 10 / 42 )Note on Specifying Breakpoints:• Due to the MCU's architecture, the following addresses cannot be set as a breakpoint.(1) Addresses (4

( 11 / 42 )IMPORTANTNotes on Target System:• The power to the MCU can be turned off and back on again during target program execution.However, because

( 12 / 42 )MEMO

( 13 / 42 )Chapter 2. PreparationThis chapter describes the package components, the system configuration and the preparation for using this product fo

( 14 / 42 )Chapter 2. Preparation2.1 TerminologySome specific words used in this user's manual are defined as follows:Emulator systemThis means a

( 15 / 42 )2.2 Package ComponentsThe M32100T-EZ-E package consists of the following items. When unpacking, check to see if itcontains all of these ite

( 16 / 42 )2.3 System Configuration of the M32100T-EZ-EBecause the M32100T-EZ-E uses a debug interface SDI (Scale Debug Interface) built in the MCU,JT

( 17 / 42 )NameON/OFFOFFONOFFMeaningEmulator system is turned off.Emulator system is turned on.Emulator system is not operating normally.1.Emulator ha

Notice 1. All information included in this document is current as of the date this document is issued. Such information, however, is subject to chang

( 18 / 42 )2. Target status LEDsThe target status LEDs indicate the status of the target MCU's operation and the target board'spower supply,

( 19 / 42 )(2) Names and Functions of Parts on the Side PanelFigure 2.3 Name of each part on the side panel1. Reset control switchThe reset control sw

( 20 / 42 )(4) Names and Functions of Parts on the Rear PanelFigure 2.5 Name of each part on the rear panel1. Maintenance switchIf this switch is pres

( 21 / 42 )Chapter 3. SetupThis chapter describes switch settings required for using this product and how to connect this product to the host machinea

( 22 / 42 )Figure 3.2 USB interface connection procedure*1 For installation, refer to "Installing the USB Device Driver" of the PD32RM user&

( 23 / 42 )3.2 Connecting the Target SystemThe M32100T-EZ-E supports JTAG connection to connect to the target board.To connect the emulator to the tar

( 24 / 42 )Figure 3.4 Sample circuit of the SDI MCU control interfaceThe following must be observed in designing a target system when you connect the

( 25 / 42 )(3) Emulator Side Circuit DiagramFigure 3.5 shows the circuit diagram in the emulator of the SDI trace interface part, and Table 3.3 listst

( 26 / 42 )MEMO

( 27 / 42 )Chapter 4. UsageThis chapter describes from turning on the power of this product to starting up the emulator debugger.4.1 Turning on the Po

M32100T-EZ-EUser’s ManualUser’s ManualRev.2.00 2003.09SDI Emulator System for M32R Family

( 28 / 42 )Chapter 4. Usage4.1 Turning on the Power Supply(1) Checking the Connections of the SystemBefore turning on the power, check the connections

( 29 / 42 )4.2 Downloading Firmware(1) When It is Necessary to Download FirmwareIt is necessary to download the firmware in the occasions listed below

( 30 / 42 )MEMO

( 31 / 42 )Chapter 5. SpecificationsThis chapter describes specifications of this product.5.1 Specifications ...

( 32 / 42 )Applicable MCUEmulation memorySoftware breakCommunications interfaceConnection type for target boardPower supplyExternal dimensions(main bo

( 33 / 42 )Chapter 6. TroubleshootingThis chapter describes how to troubleshoot when this product does not work properly.6.1 Flowchart to Remedy Troub

( 34 / 42 )Init dialog box of the emulatordebugger displayedLED display ofthe emulatorChapter 6. Troubleshooting6.1 Flowchart to Remedy TroublesFigure

( 35 / 42 )6.2 When the Emulator Debugger Does Not Start Up Properly(1) When the LED Display of the M32100T-EZ-E is AbnormalTable 6.1 LED's abnor

( 36 / 42 )Error• Communication ERROR. Can't send data.• The version of PD32RM and the firmwareon the target are not same.• Target MCU is reset s

( 37 / 42 )Chapter 7. Maintenance and GuaranteeThis chapter describes how to maintenance, repair provisions and how to request for repair.7.1 Maintena

( 2 / 42 )Keep safety first in your circuit designs!• Renesas Technology Corporation and Renesas Solutions Corporation put the maximum effort into mak

( 38 / 42 )Chapter 7. Maintenance and Guarantee7.1 MaintenanceIf dust or dirt collects on any equipment of your emulation system, wipe it off with a d

( 39 / 42 )7.4 How to Request for RepairIf your M32100T-EZ-E is found faulty, follow the procedure below to send your product for repair.CustomersWrit

( 40 / 42 )MEMO

M32100T-EZ-E User's ManualRev.2.00September 1, 2003REJ10J0002-0200ZCOPYRIGHT ©2003 RENESAS TECHNOLOGY CORPORATIONAND RENESAS SOLUTIONS CORPORATIO

1753, Shimonumabe, Nakahara-ku, Kawasaki-shi, Kanagawa 211-8668 JapanM32100T-EZ-EREJ10J0002-0200ZUser’s Manual

( 3 / 42 )PrefaceThe M32100T-EZ-E is an emulator system using the internal debug interface SDI (Scalable DebugInterface) of the M32R Family MCUs. Usin

( 4 / 42 )ContentsChapter 1. Precautions for Safety ...51.1 Sa

( 5 / 42 )Chapter 1. Precautions for SafetyThis chapter describes precautions for using this product safely and properly. For precautions of the emula

( 6 / 42 )Chapter 1. Precautions for SafetyIn both the user's manual and on the product itself, several icons are used to insure proper handlingo

( 7 / 42 )WARNINGWarnings for AC Power Supply:• Power is supplied via the USB interface cable. Therefore, do not try to modify or forcibly insert it.I