Renesas SuperH SH7200 Series Manual de usuario

Revision Date: Apr. 10, 2007Renesas Microcomputer Development Environment SystemSuperH™ Family / SH7200 Series SH7260 Series E10A-USB for SH

4 5 mm2-5767004-2Target systemE10A-USB optional 38-pin user system interface cableH-UDI port connector (top view): Area to be kept free of other com

5 AUDCKN.C.TCKGNDAU DATA 0GNDAU DATA 1GNDGNDGNDGNDGNDGNDGNDAU DATA 2AU DATA 3UVCCTMSGNDN.C.GND(GND)TDIGNDGNDGNDGNDGNDGNDGNDTDO12345678910111213141516

6 Pin 1 markNotes: 1. Input to or output from the user system.2. The symbol (_) means that the signal is active-low.3. The emulator monitors the GND

7 N.C.N.C._ASEMD (GND)TCKN.C._AUDSYNCN.C.N.C.AUDATA0AUDATA1UVCC_AUDN.C.N.C.TMS_UCON (GND)N.C.AUDCKUVCCN.C.N.C._RESTDIH-UDI port connector (top view)U

8 1.5 Recommended Circuit between the H-UDI Port Connector and the MCU 1.5.1 Recommended Circuit (36-Pin Type) Figure 1.5 shows a recommended circ

9 When the circuit is connected as shown in figure 1.5, the switches of the emulator are set as SW2 = 1 and SW3 = 1. For details, refer to section 3.

10 1.5.2 Recommended Circuit (14-Pin Type) Figure 1.6 shows a recommended circuit for connection between the H-UDI port connector (14 pins) and the

11 When the circuit is connected as shown in figure 1.6, the switches of the emulator are set as SW2 = 1 and SW3 = 1. For details, refer to section 3

12 1.5.3 Recommended Circuit (38-Pin Type) Figure 1.7 shows a recommended circuit for connection between the H-UDI and AUD port connectors (38 pins

13 When the circuit is connected as shown in figure 1.7, the switches of the emulator are set as SW2 = 1 and SW3 = 1. For details, refer to section 3

14 Note: When the emulator is used, the AUD trace mode is set without using AUDMD or _AUDRST. If those functions are enabled, do not set these pins

15 Section 2 Software Specifications when Using the SH7201 or SH7261 2.1 Differences between the MCU and the Emulator 1. When the emulator system

16 3. Low-Power States • When the emulator is used, the sleep state can be cleared with either the clearing function or with the [STOP] button, and

17 Table 2.3 Stopping Time by Memory Access (Reference) Method Condition Stopping Time H-UDI read/write Reading of one longword for the internal

18 8. Operation while Cache is Enabled When cache is enabled, the emulator operates as shown in table 2.4. Table 2.4 Operation while Cache is En

19 9. Multiplexing the AUD Pins The AUD pin is multiplexed as shown in table 2.5. Table 2.5 Multiplexed Functions Function 1 Function 2 PF2/TCLK

20 11. Loading Sessions Information in [JTAG clock] of the [Configuration] dialog box cannot be recovered by loading sessions. Thus the TCK value wi

21 • CD-ROM When the emulator is in use, the CD-ROM decoder cannot be accessed in the module standby state. Clear the module standby state before ac

22 When the emulator is used, note the following to avoid H-UDI read/write access: • Display of the toolchip on the C source ⎯ Disabling H-UDI re

23 2.2 Specific Functions for the Emulator when Using the SH7201 or SH7261 2.2.1 Event Condition Functions The emulator is used to set event condit

1. This document is provided for reference purposes only so that Renesas customers may select the appropriate Renesas products for their use.

24 Table 2.9 Dialog Boxes for Setting Event Conditions Function Dialog Box Address Bus Condition (Address) Data Bus Condition (Data) Bus S

25 Sequential Setting: Using the [Combination action (Sequential or PtoP)] dialog box specifies the sequential condition and the start or end of per

26 Table 2.10 Conditions to Be Set (cont) Classification Item Description [Ch4, 5] list box Setting is disabled in this MCU. Don’t care [Don’

27 Usage Example of Sequential Break Extension Setting: A tutorial program provided for the product is used as an example. For the tutorial program,

28 Figure 2.1 [Source] Window at Execution Halted (Sequential Break) If the sequential condition or performance measurement start/end is set, con

29 7. If the settings of the Event condition or the sequential conditions are changed during execution of the program, execution will be suspended

30 Table 2.12 shows the type numbers that the AUD function can be used. Table 2.12 Type Number and AUD Function Type Number AUD Function HS0005KC

31 To set the AUD trace acquisition mode, click the [Trace] window with the right mouse button and select [Setting] from the pop-up menu to display t

32 When the AUD trace function is used, select the [AUD function] radio button in the [Trace type] group box of the [Trace mode] page. (a) Branch Tr

33 Figure 2.3 [AUD Branch trace] Page (b) Window Trace Function Memory access in the specified range can be acquired by trace. Two memory ranges c

34 [Setting Method] (i) Select the [Channel A] and [Channel B] check boxes in the [AUD function] group box of the [Trace mode] page. Each channel

35 Note: When [M-Bus] or [I-Bus] is selected, the following bus cycles will be traced. • M-Bus: A bus cycle generated by the CPU is acquired. A bus

36 7. If breaks occur immediately after executing non-delayed branch and TRAPA instructions and generating a branch due to exception or interrupt,

37 in advance because a user stack is to be used. By default, use of a user stack is disabled. For details on the command, refer to the help file.

38 (a) Specifying the measurement start/end conditions The measurement start/end conditions are specified by using Event Condition 1,2. The [Ch1,2,

39 Note: When [Ch2 to Ch1 PA] or [Ch1 to Ch2 PA] is selected, to execute the user program, specify conditions set in Event Condition 2 and Event Con

40 Table 2.15 Measurement Item Selected Name Option Disabled None Elapsed time AC (The number of execution cycles (Iφ) is set as the measuremen

41 Notes: 1. In the non-realtime trace mode of the AUD trace, normal counting cannot be performed because the generation state of the stall or the

42

SuperH™ Family E10A-USB EmulatorAdditional Document for User's ManualSupplementary Information on Using the SH7201 a

iContents Section 1 Connecting the Emulator with the User System ...1 1.1 Components of the Emulator ...

Sales Strategic Planning Div. Nippon Bldg., 2-6-2, Ohte-machi, Chiyoda-ku, Tokyo 100-0004, Japanhttp://www.renesas.comRefer to

SuperH™ Family E10A-USB Emulator Additional Document for User’s Manual Supplementary Information on Using the SH720

ii

1 Section 1 Connecting the Emulator with the User System 1.1 Components of the Emulator The E10A-USB emulator supports the SH7201 and SH7261 (R5S7

2 1.2 Connecting the Emulator with the User System To connect the E10A-USB emulator (hereinafter referred to as the emulator), the H-UDI port conne

3 1.3 Installing the H-UDI Port Connector on the User System Table 1.3 shows the recommended H-UDI port connectors for the emulator. Table 1.3 Re