Renesas R8C/15 Información técnica Pagina 166
- Pagina / 279
- Tabla de contenidos
- MARCADORES
Valorado. / 5. Basado en revisión del cliente
R8C/14 Group, R8C/15 Group 15. Clock Synchronous Serial I/O with Chip Select (SSU)
Rev.2.10 Jan 19, 2006 Page 152 of 253
REJ09B0164-0210
15.3 Interrupt Requests
SSU has five interrupt requests : transmit data empty, transmit end, receive data full, overrun error and
conflict error. Since these interrupt requests are assigned to the SSU interrupt vector table, determining
interrupt sources by flags is required. Table 15.2 shows the SSU Interrupt Requests.
CEIE, RIE, TEIE and TIE : Bits in SSER register
ORER, RDRF, TEND and TDRE : Bits in SSSR register
Generation conditions of Table 15.2 are met, a SSU interrupt request is generated.Set the each interrupt
source to “0” by a SSU interrupt routine.
However, the TDRE and TEND bits are automatically set to “0” by writing the transmit data to the SSTDR
register and the RDRF bit is automatically set to “0” by reading the SSRDR register. When writing the
transmit data to the SSTDR register, at the same time the TDRE bit is set to “1” (data is transmitted from
the SSTDR to SSTRSR registers) again and when setting the TDRE bit to “0” (data is not transmitted
from the SSTDR to SSTRSR registers), additional 1-byte data may be transmitted.
Table 15.2 SSU Interrupt Requests
Interrupt Request Abbreviation Generation Condition
Transmit Data Empty TXI TIE=1, TDRE=1
Transmit End TEI TEIE=1, TEND=1
Receive Data Full RXI RIE=1, RDRF=1
Overrun Error OEI RIE=1, ORER=1
Conflict Error CEI CEIE=1, CE=1
- To our customers 1
- R8C/14 Group 3
- R8C/15 Group 3
- How to Use This Manual 5
- 3. M16C Family Documents 6
- Table of Contents 7
- 10. Protection 55 9
- 11. Interrupt 56 9
- 12. Watchdog Timer 78 9
- 13. Timers 83 9
- 14. Serial Interface 125 10
- 16. A/D Converter 168 10
- 18. Flash Memory Version 191 11
- 20. Precautions 235 11
- SFR Page Reference 13
- R8C/14 Group, R8C/15 Group 15
- 1. Overview 15
- 1.2 Performance Overview 16
- 1.3 Block Diagram 18
- Type No. R 5 F 21 14 4 D SP 19
- Type No. R 5 F 21 15 4 D SP 20
- 1.5 Pin Assignments 21
- 1.6 Pin Description 22
- 2.8.10 Reserved Bit 26
- 3. Memory 27
- 3.2 R8C/15 Group 28
- Table 4.2 SFR Information(2) 30
- Table 4.3 SFR Information(3) 31
- Table 4.4 SFR Information(4) 32
- 5. Reset 33
- to P3_5, P3_7 Input Port 34
- to P4_7 Input Port 34
- 5.1 Hardware Reset 35
- 5.1.2 Power on 35
- Power Supply 36
- Voltage Detection 36
- 5.2 Power-On Reset Function 37
- 5.3 Voltage Monitor 1 Reset 38
- 5.4 Voltage Monitor 2 Reset 38
- 5.5 Watchdog Timer Reset 38
- 5.6 Software Reset 38
- 6. Voltage Detection Circuit 39
- Figure 6.5 VW1C Register 43
- Figure 6.6 VW2C Register 44
- 6.1.1 Monitoring Vdet1 45
- 6.1.2 Monitoring Vdet2 45
- 6.2 Voltage Monitor 1 Reset 46
- 7. Processor Mode 49
- Figure 7.2 PM1 Register 50
- 9. Clock Generation Circuit 52
- Figure 9.2 CM0 Register 54
- Figure 9.3 CM1 Register 55
- Figure 9.4 OCD Register 56
- Figure 9.5 HRA0 Register 57
- 9.1 Main Clock 59
- 9.2 On-Chip Oscillator Clock 60
- 9.4 Power Control 62
- 9.4.1 Normal Operating Mode 62
- 9.4.2.4 Exiting Wait Mode 64
- 9.4.3 Stop Mode 65
- 9.4.3.1 Entering Stop Mode 65
- 9.4.3.3 Exiting Stop Mode 65
- 10. Protection 69
- 11. Interrupt 70
- 11.1.2 Software Interrupts 71
- 11.1.2.2 Overflow Interrupt 71
- 11.1.2.3 BRK Interrupt 71
- 11.1.5.1 Fixed Vector Tables 73
- 11.1.6 Interrupt Control 75
- Figure 11.4 INT0IC Register 76
- 11.1.6.1 I Flag 77
- 11.1.6.2 IR Bit 77
- 11.1.6.4 Interrupt Sequence 78
- Instruction in 79
- 11.1.6.7 Saving a Register 80
- 11.1.6.9 Interrupt Priority 81
- Level 0 (default value) 82
- 11.2 INT Interrupt 83
- 11.2.1 INT0 Interrupt 83
- 11.2.2 INT0 Input Filter 84
- Timer X Mode Register 85
- 11.2.4 INT3 Interrupt 86
- Figure 11.16 TCC1 Register 87
- 11.3 Key Input Interrupt 88
- Figure 11.18 KIEN Register 89
- 11.4 Address Match Interrupt 90
- 12. Watchdog Timer 92
- 13. Timers 97
- CNTRSEL=1 98
- CNTRSEL=0 98
- Figure 13.2 TXMR Register 99
- REJ09B0164-0210 100
- 13.1.1 Timer Mode 101
- 13.1.2 Pulse Output Mode 102
- 13.1.3 Event Counter Mode 104
- Input polarity selected to 112
- Figure 13.12 TZMR Register 113
- Figure 13.15 TCSS Register 116
- 13.2.1 Timer Mode 117
- • When count starts 119
- Timer Z Mode Register 127
- PREZ=01h, TZPR=01h, TZSC=02h 128
- 13.3 Timer C 129
- Timer C Register 131
- Figure 13.27 TCC0 Register 132
- Figure 13.28 TCC1 Register 133
- Figure 13.29 TCOUT Register 134
- 13.3.1 Input Capture Mode 135
- ←Measurement value 1 136
- ←Measurement value 2 136
- 13.3.2 Output Compare Mode 137
- 14. Serial Interface 139
- UART0 Bit Rate Register 141
- Set to “001b” 145
- 14.2.2 Bit Rate 153
- Figure 15.2 SSCRH Register 156
- SS Control Register L 157
- 15.1 Transfer Clock 163
- 15.3 Interrupt Requests 166
- 15.5.2 Data Transmit 169
- 15.5.3 Data Receive 171
- 15.5.4 Data Transmit/Receive 173
- I/O Pin and SS Shift Register 175
- 15.1.1 Association 175
- 15.6.2 Data Transmit 177
- 15.6.3 Data Receive 179
- 16. A/D Converter 182
- 16.1 One-Shot Mode 186
- 16.2 Repeat Mode 188
- 16.3 Sample and Hold 190
- 16.4 A/D Conversion Cycles 190
- 17. Programmable I/O Ports 193
- P1_0 to P1_3 194
- P1_6, P1_7 195
- P3_4, P3_5, P3_7 195
- P4_6/XIN 196
- P4_7/XOUT 196
- 17.4 Port setting 200
- 17.5 Unassigned Pin Handling 204
- 18. Flash Memory Version 205
- 18.2 Memory Map 207
- 18.3.1 ID Code Check Function 209
- Figure 18.4 OFS Register 210
- 18.4 CPU Rewrite Mode 211
- 18.4.1 EW0 Mode 212
- 18.4.2 EW1 Mode 212
- Full Status Check 213
- 18.4.2.10 FMR40 bit 214
- 18.4.2.11 FMR41 bit 214
- 18.4.2.12 FMR46 bit 214
- EW1 Mode Operating Procedure 217
- →wait until oscillation 218
- 18.4.3 Software Commands 219
- 18.4.3.1 Read Array Command 219
- 18.4.3.4 Program Command 220
- 18.4.3.5 Block Erase 221
- 18.4.4 Status Register 223
- 18.4.5 Full Status Check 224
- 18.5 Standard Serial I/O Mode 226
- 18.5.1 ID Code Check Function 226
- R8C/14, R8C/15 228
- 18.6 Parallel I/O Mode 230
- SSO(Output) 240
- SSI(Input) 240
- VCC = 5V 244
- VCC = 3V 248
- 20. Precautions 249
- 20.2 Interrupts 250
- 20.2.1 Reading Address 00000h 250
- 20.2.2 SP Setting 250
- 20.3 Clock Generation Circuit 253
- 20.4 Timers 254
- 20.4.1 Timers X and Z 254
- 20.4.2 Timer X 254
- 20.4.3 Timer Z 255
- 20.4.4 Timer C 255
- 20.5 Serial Interface 256
- 20.7 A/D Converter 258
- 20.8 Flash Memory Version 259
- 20.8.1 CPU Rewrite Mode 259
- 20.8.1.1 Operating Speed 259
- 20.8.1.3 Interrupts 259
- 20.8.1.9 Interrupt Request 260
- Generation during Auto-erase 260
- Operation in EW1 Mode 260
- 20.9 Noise 262
- Debugging Emulator 265
- Register Index 267
- REVISION HISTORY 268
- → “INT1” 271
- → Figure 18.16 276
- “8.16” → “8.56” 277
- Rev.2.10 Jan 19, 2006 278
- Renesas Technology Corp 278
- Hardware Manual 279
Relacionado con productos y manuales para Redes Renesas R8C/15
Redes Renesas H8S/2378F Información técnica
(170 paginas)
(170 paginas)
Redes Renesas Emulator System E8 Información técnica
(34 paginas)
(34 paginas)
Redes Renesas HS2378KCI01H Información técnica
(42 paginas)
(42 paginas)
Redes Renesas Emulator System E8 Información técnica
(55 paginas)
(55 paginas)
Redes Renesas SuperH SH7710 E10A Información técnica
(42 paginas)
(42 paginas)
Redes Renesas 70 Información técnica
(49 paginas)
(49 paginas)
Redes Renesas HS1653ECN61H Manual de usuario
(322 paginas)
(322 paginas)
Redes Renesas SuperH SH7285 Manual de usuario
(60 paginas)
(60 paginas)
Redes Renesas SuperH SH7700 Series Manual de usuario
(27 paginas)
(27 paginas)
© 2020, manymanuals.es. Todos los derechos reservados | 0.065 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comentarios a estos manuales