Renesas H8S/2628 Información técnica Pagina 396
- Pagina / 430
- Tabla de contenidos
- SOLUCIÓN DE PROBLEMAS
- MARCADORES
Valorado. / 5. Basado en revisión del cliente
368
8.2 Notes on Usage of the H8S/2628 E6000 Emulator
There are the following notes on usage of the emulator.
8.2.1 Environment for Execution of the Tutorial Program
To execute the tutorial program, specify “Tutorial.hws” stored in the following directory:
HEW installation destination directory\Tools\Renesas\DebugComp\Platform\E6000\2628\Tutorial
8.2.2 I/O Register Differences between the Actual MCU and the Emulator
In the E6000 emulator, one evaluation chip emulates several types of MCU. Therefore, there are some
differences in I/O registers between an actual MCU and the emulator. Note these differences when accessing the
I/O registers.
I/O port is in the input state at default. The I/O register contents indicate the emulator port status. When the user
system interface cable is not connected, the read value is 1 due to pull-up resistors.
In the emulator, accesses to the following registers for controlling the flash memory are invalid.
• RAM emulation register (RAMER: H'FEDB)
• Flash memory control register 1 (FLMCR1: H'FFA8)
• Flash memory control register 2 (FLMCR2: H'FFA9)
• Block register 1 (EBR1: H'FFAA)
• Block register 2 (EBR2: H'FFAB)
Note: The addresses indicate the lower 16 bits.
8.2.3 Access to the Reserved Area
When accessing the reserved area, note the following:
If the reserved area is used, the operation in the actual MCU cannot be guaranteed. If the user program extends
to the reserved area during debugging, select the MCU having the largest ROM capacity (for example, debug the
H8S/2627 program in the H8S/2628 mode).
8.2.4 Support of Flash Memory
This emulator does not emulate the flash memory in the MCU.
8.2.5 Hardware Standby
This emulator does not support the hardware standby function. Therefore, checking [User Standby enable] in the
[Configuration Properties] dialog box is invalid.
- To our customers 1
- H8S/2628 E6000 3
- Cautions 5
- IMPORTANT INFORMATION 7
- LIMITED WARRANTY 8
- DISCLAIMER 8
- SAFETY PAGE 10
- CAUTION 12
- Introduction 13
- About This Manual 14
- Contents 15
- HEW Part 25
- 1. Overview 27
- 1.2 The Main Window 28
- 1.3 The Help System 35
- 1.4 Launching the HEW 36
- 1.5 Exiting the HEW 36
- 2. Build Basics 37
- 2.2 Project Files 38
- .SRC .ASM .MAR .C .LIB .LPF 44
- 2.5 Build Configurations 50
- 2.6 Building a Project 53
- 2.7 File Dependencies 56
- 3. Advanced Build Features 63
- 3.3 Ordering Build Phases 69
- 3.5 File Mappings 78
- 3.6 Controlling the Build 80
- 3.7 Logging Build Output 81
- 3.10 Generating a Makefile 84
- 4. Using the Editor 85
- 4.4 Editing a File 91
- 4.6 Bookmarks 96
- 4.7 Printing a File 96
- 4.8 Configuring Text Layout 97
- 4.9 Splitting a Window 100
- 4.10 Configuring Text 101
- 4.11 Syntax Coloring 102
- 4.12 Templates 104
- 5. Tools Administration 109
- 5.1 Tool Locations 110
- 5.3 Registering Components 111
- 5.4 Unregistering Components 112
- 5.8 Custom Project Types 118
- 6.1 Customizing the Toolbar 119
- 6.6 Customizing File Save 129
- 7. Version Control 133
- 8.3 Specifying Arguments 144
- 8.4 Controlling Execution 152
- 9. Using Visual SourceSafe 155
- Emulator Debugger Part 161
- Section 1 Overview 163
- 1.2 Warnings 164
- 1.3 Environmental Conditions 165
- 2.1 Emulator Preparation 167
- User system interface 168
- IC socket 168
- Emulator 169
- User system interface cable 169
- 2.4 Power Supply 170
- 2.5 SIMM Memory Module 170
- 2.6 Hardware Interface 171
- Trigger output 172
- 2.7 System Check 174
- Figure 2.17 HEW Window 177
- 2.8 Communication Problems 178
- 3.1 Debugging Features 179
- 3.3 Hardware Features 181
- 3.4 Stack Trace Function 182
- 3.5 Online Help 182
- 4.4 Debugger Sessions 196
- 4.6 Ending the Emulator 201
- Section 5 Debugging 203
- [General] page 204
- 5.2 Downloading a Program 209
- 5.4 Viewing the Registers 217
- 5.5 Operating Memory 219
- 5.6 Viewing the I/O Memory 227
- 5.10 Viewing the Labels 236
- 5.11 Executing Your Program 241
- 5.12 Stopping Your Program 245
- 5.13 Elf/Dwarf2 Support 247
- 5.14 Viewing the Variables 251
- 5.15 Using the Event Points 258
- 5.20 Analyzing Performance 315
- Section 6 Tutorial 327
- 6.2 Running the HEW 328
- 6.5 Setting Registers 332
- 6.6 Executing the Program 333
- 6.7 Reviewing Breakpoints 335
- 6.8 Referring to Symbols 336
- 6.9 Viewing Memory 337
- 6.10 Watching Variables 338
- 6.14 Resetting the MCU 346
- 6.15 Break Function 347
- 6.16 Trace Functions 353
- 6.17 Stack Trace Function 368
- 6.19 Monitor Function 372
- 6.20 What Next? 376
- 7.2 User System Interface 378
- Debugging Platform Remark 381
- [Custom Device] page 386
- [Custom Device] page (cont) 387
- 8.1.11 Trace Information 392
- Appendix A Troubleshooting 399
- Appendix C Placeholders 403
- C.3 Available Placeholders 405
- C.4 Placeholder Tips 407
- Appendix D I/O File Format 409
- Appendix F Menus 415
- Table F.1 GUI Menus (cont) 416
- Appendix G Command Lines 419
- Message Description 425
- H8S/2628 E6000 Emulator 430
- User’s Manual 430
Relacionado con productos y manuales para Software Renesas H8S/2628
(26 paginas)© 2020, manymanuals.es. Todos los derechos reservados | 0.062 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comentarios a estos manuales