Renesas SuperH SH7343 Información técnica descargar pdf (Pagina 49)

Target interface (SH7243F/SH7285F/ SH7286F) Aug. 2, 2010 (Fourth Edition)

■ SH7243F/SH7285F/ SH7286F

Applicable product PALMiCE3-SH

Applicable connectors

(Connectors for debugger)

MIL connector (14-pin design)

MDR connector (36-pin design)

Mictor connector (38-pin design)

NB : When you use PALMiCE3-SH AUD360 model and if you are using CPU with voltage over 4.0V, please contact us.

MIL connector

Signals

CPU Pin No. CPU Pin No.

SH7243F SH7285F SH7286F SH7243F SH7285F SH7286F

No.

Signal

Input/

Output

LQFP-100

(FP-100UV)

LQFP-144

(FP-144LV)

LQFP-176

(FP-176AV,

FP-176EV)

No.

Signal

Input/

Output

LQFP-100

(FP-100UV)

LQFP-144

(FP-144LV)

LQFP-176

(FP-176AV,

FP-176EV)

1 TCK Input 8 133 91 2 N.C.

3 TRST Input 10 135 93 4

GND

(

ASEMD0)

(Input) (78) (115) (135)

5 TDO Output 7 132 90 6 GND

ASEBRKAK/

ASEBRK

Input/

Output

77 114 134 8 VCC

Output

9 TMS Input 9 134 92 10 GND

11 TDI Input 6 131 89 12 GND

13 RES Output 76 113 133 14 GND

・ For the pin where stated as N.C. in the table, leave the signal unconnected.

*1: Input/output is based on the target system.

*2: To debug,

ASEMD0 pin needs to be brought to Low state.

Shown in the target connection reference diagram is the circuit that brings ASEMD0 pin to Low state when you connect ASEMD0 signal to the connector for

debugger.

If you do not connect ASEMD0 signal to Pin No. 4 of the connector for debugger, the circuit that sets ASEMD0 pin by switch circuit will do. However, in such case,

do not connect ASEMD0 pin to Pin No. 4 of the connector for debugger, but connect Pin No. 4 of connector for the debugger to GND.

*3: For VCC, connect I/O power of CPU.

Target connection reference diagram

SH7243F/SH7285F

SH7286F

*1: RES, which is connected to Pin No. 13 of the connector for debugger, is the signal that debugger uses for monitoring the state of RES pin of CPU.

*2:

ASEBRKAK/ASEBRK (Output/Input signals) are multiplexed with FWE (Input signal) in a pin. To allow the operation of the user target alone

when you use the ICE, in making signal arrangement, do not connect the pin to VCC nor GND directly, but connect it to a pull-up resistor with

ohmic value of 4.7K or a pull-down resistor with ohmic value of 100k.

MIL connector specifications

Recommended connector

Manufacturer Omron Corporation

Model XG4C-1431

(Top view on the target board)

(For detailed dimensions of the connector, refer

to the documentation by manufacturer of the

connector.)

*Please look at the pin configuration diagram

above and make sure that the connector is in

the right direction before connecting.

Please check the pin number in the signal table

above and make sure the signal and the pin

numbers match.

1 2 ... 44 45 46 47 48 49 50 51 52 53 54 ... 203 204

Comentarios a estos manuales

Sin comentarios

Renesas SuperH SH7343 Información técnica Pagina 49

Comentarios a estos manuales

Relacionado con productos y manuales para Redes Renesas SuperH SH7343