Renesas Emulation Pod M306H2T-RPD-E Información técnica Pagina 38
- Pagina / 68
- Tabla de contenidos
- SOLUCIÓN DE PROBLEMAS
- MARCADORES
Valorado. / 5. Basado en revisión del cliente
M306H5T3-RPD-E User’s Manual 3. Usage
REJ10J0866-0100Z Rev.1.00 Dec.16, 2004
Page 36 of 66
3. Usage
This chapter describes the setting when you use this product for the first time and the workflow, from turning on the power of
this product to starting up the emulator debugger.
.
3.1 When Using This Product for the First Time
3.1.1 Making an MCU File
It is necessary to make an MCU file to use this product with the emulator debugger M3T-PD30. According to the MCU you
use, change the contents of the MCU file. Make the MCU file following the description below using a text editor and store it in
the "mcufiles" folder in the directory where the emulator debugger is installed.
The MCU file contains information such as, SFR area, internal RAM area, internal ROM area, firmware file name. The
contents of the MCU file when using the M306H5FGFP (8KB RAM, 256KB ROM) are as follows:
0 : SFR area Start address
3FF : End address
400 : Internal RAM Start address
23FF : End address
C0000 : Internal ROM Start address
FFFFF : End address
M30620P : Name of firmware (Do not change.)
0 : Expansion No. (Do not change.)
When using this product in microprocessor mode, set the internal ROM area as follows.
00000 : Internal ROM Start address
00001 : End address
3.1.2 Setting the Work Area
With this product, the emulator uses 54 bytes as a work area in emulation memory. Therefore, according to the memory
mapping of the MCU you use, specify the work area addresses.
In single-chip mode, set the work area address at 10000h.
In memory expansion or microprocessor mode, the areas listed below cannot be used as a work area, specify a work area other
than the areas listed below. And the top address of the work area should be an even-numbered address.
(1) SFR area (0000h--003FFh)
(2) External area of multiplex bus setting
(3) Reserved area of 27000h--27FFFh
(4) Stack area used by the emulator for reset command execution (0FFF9h--0FFFFh)
The area used as a work area (54 bytes) is specified in the F/W and Work Area tab of the INIT dialog box of the emulator
debugger M3T-PD30. And set the work area as MAP=INT.
- La politique soviétique 0
- The Realism of Khrushchev 1
- LLEN, op. cit., p. 61 3
- Le volume des échanges 4
- La structure des échanges 5
- LLEN, op. cit., p. 26 6
- AHMOUD le 8 7
- AWAN, L. 8
- AWAN, op. cit., p. 184 8
- Le bilatéralisme 9
- ERLINER, . op. cit, p. 81 10
- LLEN, op. cit., p. 32 10
- COTT. loc. cit., p. 46 10
- Les points de friction 11
- CHAPITRE VI 15
- Amérique latine 16
- ERLINER, op. cit., p. 38 17
- La République Arabe Unie 18
- CPR, 19 janvier 1959 20
- op. cit. 21
- AO TSÉ-TOUNG, La 23
- La Syrie 24
- Le Yémen 26
- Le Liban et le Soudan 27
- TROISIEME PARTIE 28
- CHAPITRE VII 29
- ONOMAREV, B. O 34
- loc. cit., p. 67 38
- CHAPITRE VIII 49
- ELJAJEV 50
- ONOMAREV, loc. cit., p. 42 52
- QUATRIEME PARTIE 55
- L’unification et ses dangers 57
- OHI ED-DIN 61
- pp. 121-154 63
- communistes locaux 65
- Izvestia, l 67
- Le conflit arabo-israélien 71
- LLEN, op. cit., p. 19 77
- Documents, 1957, p. 263 80
- BIBLIOGRAPHIE 82
- TRAVAUX 86
- b) Articles 90
- REVUES DES REVUES 103
- NOTE SUR L’AUTEUR 108
- Pravda, 18 April 1956 110
- - Introduction 111
- PUBLISHER’S PREFACE 120
- PREMIERE PARTIE 122
- - Chapitre I 123
- CHAPITRE II 127
- Epilogue 139
- 1. LA QUESTION DE L’ARMEMENT 140
- L'Egypte 141
- Victor Segesvary 142
- ALLIN, op. cit. p. 394 143
- ALLIN, op. cit. p. 395 143
- La Syrie 144
- L'Arabie Saoudite 145
- Le Liban 145
- Le Yémen 145
- L'Irak 146
- ERCHITZ dans Sovjetskaja 149
- TABLE DES MATIÈRES 153
- ALLIN, op. cit., p. 416 162
- La doctrine Eisenhower 168
- La réplique soviétique 169
- La riposte arabe 173
- ALLIN, op. cit., p. 471 177
- AW, 26 juin 1956 180
- ISHER, op. cit., p. 556 181
- La position soviétique 182
- Epilogue 188
- DEUXIEME PARTIE 189
- Le contexte général : 190
- ATOLINA qui y est cité 193
- PROCHE-ORIENT 195
- To our customers 197
- CAUTION 198
- Contents 199
- Page 10 of 66 200
- Page 11 of 66 201
- User Registration 202
- Terminology 203
- 1. Outline 204
- 1.3 System Configuration 205
- PERFORMANCE 206
- EMULATION 206
- IMPORTANT 207
- 1.4 Specifications 209
- 1.5. Operating Environment 210
- 2.2 Each Setting 212
- IC1:Inverter (Unbuffer) 214
- 2.4 Switch Settings 217
- M306H5T3-RPD-E 219
- Emulation pod 226
- 3. Usage 228
- : Blinking 234
- 4. Hardware Specifications 235
- Write timing 237
- Item Manual 241
- 4.4 Connection Diagram 244
- 4.5 External Dimensions 246
- M30 6H2T - PTC REV . A 247
- Important 252
- 5. Troubleshooting 254
- 6. Maintenance and Guarantee 258
- REJ10J0866-0100Z 261
- User’s Manual 261
- WARNING 263
- CAUTION 263
- WARNING 264
Relacionado con productos y manuales para Redes Renesas Emulation Pod M306H2T-RPD-E
Redes Renesas SH7641 Información técnica
(13 paginas)
(13 paginas)
Redes Renesas 4513 Información técnica
(99 paginas)
(99 paginas)
Redes Renesas M16C/6V Información técnica
(50 paginas)
(50 paginas)
Redes Renesas M3T-SRA74 Manual de usuario
(22 paginas)
(22 paginas)
Redes Renesas REG10J0052-0200 Manual de usuario
(16 paginas)
(16 paginas)
Redes Renesas M38000TL2-FPD Información técnica
(56 paginas)
(56 paginas)
Redes Renesas M16C/6NK Información técnica
(33 paginas)
(33 paginas)
Redes Renesas SuperH HS7630KCM02HE Manual de usuario
(36 paginas)
(36 paginas)
© 2020, manymanuals.es. Todos los derechos reservados | 0.043 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comentarios a estos manuales