Renesas User System Interface Board HS7047ECH61H Manual de usuario Pagina 239
- Pagina / 243
- Tabla de contenidos
- MARCADORES
Valorado. / 5. Basado en revisión del cliente
153
Table B.1 High-performance Embedded Workshop Commands (cont)
No. Command Name Abbreviation Function
68 PINSEL PSL Displays the current settings for selection of pins
69 PINSEL_xxxx PSLxxxx Allows settings for selection of pins (xxxx: Pin name)
70 PROFILE PR Enables or disables the profile
71 PROFILE_DISPLAY PD Displays profiling results
72 PROFILE_SAVE PS Saves profiling results
73 QUIT QU Exits High-performance Embedded Workshop
74 RADIX RA Sets default input radix
75 REFRESH RF Updates windows related to memory
76 REGISTER_DISPLAY RD Displays CPU register values
77 REGISTER_SET RS Sets CPU register contents
78 REMOVE_FILE REM Deletes the specified file from the current project
79 RESET RE Resets CPU
80 SAVE_SESSION SE Saves the current session
81 SLEEP - Delays command execution
82 STEP ST Steps program (by instructions or source lines)
83 STEP_MODE SM Sets the step mode
84 STEP_OUT SP Steps out of the current function
85 STEP_OVER SO Steps program, not stepping into functions
86 STEP_RATE SR Sets or displays rate of stepping
87 SUBMIT SU Executes a command file
88 SYMBOL_ADD SA Defines a symbol
89 SYMBOL_CLEAR SC Deletes a symbol
90 SYMBOL_LOAD SL Loads a symbol information file
91 SYMBOL_SAVE SS Saves a symbol information file
92 SYMBOL_VIEW SV Displays symbols
93 STATUS STS The content of the [Platform] sheet in the [Status]
window is displayed.
94 SAVE_WORKSPACE SW Saves the current workspace
95 TCL - Enables or disables the TCL
96 TIMER TI Sets or displays the timer resolution
97 TOOL_INFORMATION TO Outputs information on the currently registered tool to
a file
98 TRACE TR Displays trace information
99 TRACE_ACQUISITION TA Sets or displays trace acquisition parameters
100 TRACE_ACQUISITIONn TAn Sets PtoP point and each channel for trace
acquisition conditions
101 TRACE_ACQUISITION
_CLEAR
TAC Deletes trace acquisition parameters
102 TRACE_BINARY_
COMPARE
TBC Compares a trace binary file with the current trace
information
103 TRACE_BINARY_SAVE TBV Outputs trace information into a binary file
- SH7046 E6000H Emulator 1
- IMPORTANT INFORMATION 5
- LIMITED WARRANTY 6
- DISCLAIMER 6
- SAFETY PAGE 8
- Warnings on Emulator Usage 10
- CAUTION 11
- About This Manual 14
- Contents 15
- Hardware Part 19
- LAN adapter 22
- (option) 22
- USB adapter 22
- 1.3 System Configuration 27
- Enlarged 34
- Signal Name Delay Time (ns) 46
- _RES 15.0 46
- 0.65 × 19 = 12.35 ± 50
- 0.65 ± 0.05 50
- 0.50 × 24 = 12.00 ± 0.05 53
- 0.50 ± 0.05 53
- × 12 mm) 55
- 0.5 × 35 = 17.5 59
- Evaluation chip board 60
- Connector: WD-200P-VF85-N 60
- PD24/D24/_DREQ0/_UBCTRG 65
- PA2/SCK0/_DREQ0/IRQ0/ 68
- A2/PCIO/ACK2/ 68
- PA5/SCK1/_DREQ1/_IRQ1/ 68
- A5/_POE6/ACK3/ 68
- Message Description 81
- Debugger Part 85
- Section 1 Overview 87
- 2.2 Connecting the Emulator 99
- 2.4 Ending the Emulator 100
- Section 3 Debugging 101
- [Pin Select Registers] page 104
- 3.2 Downloading a Program 108
- , e.g., #PC+0x100 112
- 3.6 Looking at Variables 121
- 3.7 Using the Event Points 123
- 3.9 Analyzing Performance 152
- 3.10 Profiling Function 163
- 3.11 [Profile-Chart] Window 167
- Section 4 Tutorial 169
- 4.5 Setting Registers 174
- 4.6 Executing the Program 175
- 4.7 Reviewing Breakpoints 178
- 4.8 Referring to Symbols 179
- 4.9 Viewing Memory 180
- 4.10 Watching Variables 181
- 4.15 Break Function 190
- 4.16 Trace Functions 198
- 4.17 Stack Trace Function 210
- 4.19 Monitor Function 215
- 4.20 What Next? 217
- 5.1 Supported Hardware 219
- 5.2 Debugging Platform 219
- 5.4 Executing Your Program 221
- 5.5 Event Functions 221
- 5.6 Trace Functions 223
- 5.7 Monitor Function 224
- 5.9 Profiling Function 225
- 5.10 Input Format 225
- 5.11 Tutorial Program 226
- 5.12 Memory Map 226
- SB: Short block 227
- LB: Large block 227
- Section 6 Error Messages 229
- Appendix A Menus 233
- Table A.1 GUI Menus (cont) 235
- Appendix B Command Lines 237
- User's Manual 241
- RENESAS SALES OFFICES 242
- User’s Manual 243
Relacionado con productos y manuales para Redes Renesas User System Interface Board HS7047ECH61H
Redes Renesas 4513 Información técnica
(99 paginas)
(99 paginas)
Redes Renesas M16C/6V Información técnica
(50 paginas)
(50 paginas)
Redes Renesas M3T-SRA74 Manual de usuario
(22 paginas)
(22 paginas)
Redes Renesas REG10J0052-0200 Manual de usuario
(16 paginas)
(16 paginas)
Redes Renesas M38000TL2-FPD Información técnica
(56 paginas)
(56 paginas)
Redes Renesas M16C/6NK Información técnica
(33 paginas)
(33 paginas)
Redes Renesas SuperH HS7630KCM02HE Manual de usuario
(36 paginas)
(36 paginas)
© 2020, manymanuals.es. Todos los derechos reservados | 0.054 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comentarios a estos manuales